Part of our Contractor Guides

Markup vs margin is cost vs price: markup is profit as a percentage of cost, and margin is profit as a percentage of the selling price. The same dollars give two different percentages. A 20% markup is only a 16.7% margin, and a 25% margin needs a 33.3% markup.
For contractors the difference is not academic. If you want a 20% margin and add 20% to cost, you leave money on every job. And the margin on your estimate is gross: overhead still comes out of it before you see any profit.
This guide gives you the formulas, a conversion table, a worked example of what the mix-up costs, and how to build your own markup from your overhead. It pairs with our step-by-step estimate guide, where the markup actually lands on the page.
Margin vs markup: what is the difference?
Margin vs markup comes down to the base you divide by. Markup is how much you add to cost, expressed as a percentage of cost. Margin is how much of the selling price is profit, expressed as a percentage of price. On a job that costs $1,000 and sells for $1,250, the $250 profit is a 25% markup and a 20% margin.
Markup is always the bigger number, because cost is smaller than price. The gap widens as the percentages rise: a 100% markup (doubling your cost) is only a 50% margin.
The confusion usually starts when someone says “we work on 20%” without saying 20% of what. On every estimate, quote or bid you send, decide which one you mean. If you are unsure which document fits the job, see whether to call it a quote or an estimate.
The markup formula and the margin formula
The markup formula is markup % = (price – cost) / cost. The margin formula is margin % = (price – cost) / price. To get a price from a markup, multiply: cost x (1 + markup). To get a price from a margin, divide: cost / (1 – margin). The table collects every formula you need, each with the same $1,000 cost example.
| You want | Formula | Example ($1,000 cost) |
|---|---|---|
| Markup % | (price – cost) / cost | ($1,250 – $1,000) / $1,000 = 25% |
| Margin % | (price – cost) / price | ($1,250 – $1,000) / $1,250 = 20% |
| Price from markup | cost x (1 + markup) | $1,000 x 1.25 = $1,250 |
| Price from margin | cost / (1 – margin) | $1,000 / 0.80 = $1,250 |
| Margin from markup | markup / (1 + markup) | 0.25 / 1.25 = 20% |
| Markup from margin | margin / (1 – margin) | 0.20 / 0.80 = 25% |
How to calculate markup percentage
Subtract cost from price, then divide by cost. A bathroom fan swap that costs you $180 in labor and parts and sells for $270 has a markup of ($270 – $180) / $180 = $90 / $180 = 50%. To price from a target markup, multiply cost by one plus the markup: $180 x 1.50 = $270.
How to calculate margin percentage
Subtract cost from price, then divide by price. The same fan swap: $90 / $270 = 33.3% margin. To price from a target margin, divide cost by one minus the margin: for a 40% margin, $180 / 0.60 = $300. Note what happens if you multiply instead: $180 x 1.40 = $252, which is only a 28.6% margin.
Markup to margin conversion table
To convert markup to margin, divide the markup by one plus the markup. A 10% markup is a 9.1% margin, 25% is 20.0%, 50% is 33.3%, and 100% is 50.0%. Every value in the table below is computed from margin = markup / (1 + markup), rounded to one decimal. For any other number, use the free markup and margin calculator.
| Markup on cost | Margin on price | Price on $1,000 cost |
|---|---|---|
| 10% | 9.1% | $1,100 |
| 15% | 13.0% | $1,150 |
| 20% | 16.7% | $1,200 |
| 25% | 20.0% | $1,250 |
| 30% | 23.1% | $1,300 |
| 33.3% | 25.0% | $1,333 |
| 40% | 28.6% | $1,400 |
| 50% | 33.3% | $1,500 |
| 75% | 42.9% | $1,750 |
| 100% | 50.0% | $2,000 |
Going the other way (margin to markup): a 10% margin needs an 11.1% markup, 20% needs 25%, 30% needs 42.9%, 40% needs 66.7%, and 50% needs 100%.
Why confusing the two costs contractors money
If you want a 20% margin but add 20% to cost, you get a 16.7% margin instead. On a job with $10,000 of cost, that is $2,000 of gross profit instead of $2,500: a $500 shortfall on one job, and $20,000 across $400,000 of annual job costs.
The arithmetic: the right price for a 20% margin is $10,000 / 0.80 = $12,500. Adding 20% gives $10,000 x 1.20 = $12,000. The difference is $500, which is 5% of cost. Across a year with $400,000 of job costs, 5% is $20,000.
That $20,000 does not show up as a loss on any single job. It shows up at year end as “we were busy, so where did the money go?” The same thing happens with labor: if your hourly rate is built on the wage rather than your fully burdened labor rate, the markup is being applied to the wrong cost.
It compounds on extra work, too. Price every change order with the same margin method as the original job; the change order process should not be where your pricing gets sloppy.
Gross margin vs net margin: where overhead goes
Gross margin is what is left after job costs (labor, materials, subs, equipment). Net margin is what is left after overhead too. The margin you put on an estimate is gross, so it has to cover overhead and profit: required gross margin = (annual overhead + target net profit) / annual revenue.
Illustrative example: you expect $500,000 in revenue, your overhead is $90,000 a year, and you want $50,000 of net profit. Required gross margin = ($90,000 + $50,000) / $500,000 = 28%. The markup that produces it is 0.28 / 0.72 = 38.9%.
Check it: job costs are $500,000 x 0.72 = $360,000. $360,000 x 1.389 = $500,000 (rounded). Gross profit is $140,000; subtract $90,000 overhead and $50,000 is left. A 20% markup on the same costs would give $432,000 of revenue and $72,000 of gross profit, which does not even cover overhead.
That gives you a break-even point. On $360,000 of job costs, the markup that only covers overhead is $90,000 / $360,000 = 25%, a 20% margin. Price below it and the year loses money even if every job looks profitable on paper.
How do you choose your markup?
Build your markup from your own numbers: add your annual overhead to the net profit you want, divide by your expected revenue to get the gross margin you need, then convert that margin to a markup. A number heard on a forum does not know your overhead.

- Total last year’s overhead from your books: vehicles, insurance, office, software, phone, marketing, admin pay.
- Set a target net profit in dollars.
- Estimate next year’s revenue conservatively.
- Required gross margin = (overhead + profit) / revenue.
- Markup = margin / (1 – margin).
Make sure the cost base is right first. Labor should be at the burdened billable rate; the labor cost calculator gets you there. For overhead recovery per labor hour and contingency, see how to price overhead and contingency into a bid.
Should materials, labor and subs carry the same markup?
Not necessarily. It is a business choice. Some contractors use a lower materials markup and subcontractor markup, where clients can check prices, and a higher labor markup. Others use one blended rate. What matters is that the total job hits your required gross margin. Some contracts, especially commercial and insurance work, set or limit markup on subs, so read the contract. On a cost-plus contract, a fee stated as a percentage of cost is a markup, not a margin, so a 15% fee is a 13.0% margin on the total.
What is the average contractor markup?
There is no single average contractor markup. No official benchmark sets a typical markup across all trades, and the right number depends on your trade, job size and overhead. The closest primary data comes from NAHB’s Cost of Doing Business studies, which report margins, not markups, for builders and remodelers. Use them as context, not as your target.
NAHB reports that remodelers averaged a 29.9% gross profit margin and a 6.3% net profit margin in fiscal 2024, with operating expenses at 23.6% of revenue (NAHB Remodelers’ Cost of Doing Business Study, 2026 edition). Converted, a 29.9% gross margin is a 42.7% markup on job costs (0.299 / 0.701).
For single-family builders, NAHB reports a 20.7% average gross margin and an 8.7% net margin in fiscal 2023 (NAHB Builders’ Cost of Doing Business Study, 2025 edition). That gross margin converts to a 26.1% markup (0.207 / 0.793). Published, sourced averages for individual specialty trades are scarce; we have not found one we would cite.
The same goes for general contractor markup. A GC’s markup has to cover site supervision, overhead and profit on top of subcontractor costs, so it varies with job size and contract type. These NAHB figures are the closest sourced data on construction profit margin; your own contractor profit margin comes from your books, using the method above.
What does “10 and 10” overhead and profit (O&P) mean?
“10 and 10” means 10% overhead plus 10% profit, applied one after the other. Because the profit is calculated on cost plus overhead, the total is 21% on cost (1.10 x 1.10 = 1.21), not 20%. As a margin, that is 17.4% of the price.
On $10,000 of cost: overhead brings it to $11,000, and profit brings it to $12,100. The $2,100 of overhead and profit is 21% of cost and 17.4% of the $12,100 price ($2,100 / $12,100). The profit alone, $1,100, is a 9.1% margin.
The term is common in insurance restoration estimating. Whether a carrier allows O&P on a claim, and at what rate, depends on the carrier, the policy and the claim, so do not assume a fixed rule.
Once the price is set, the job still has to be billed and collected. On long jobs that means billing by percent complete; on short ones, a sample contractor invoice shows how to lay out the final bill, and clear invoice payment terms keep the margin from leaking into late payments. If you would rather have software do the math, see how Joist, Invoice2go and Jobber compare.
Frequently Asked Questions
Is a 50% markup the same as a 50% margin?
No. A 50% markup on a $1,000 cost gives a $1,500 price, and the $500 profit is a 33.3% margin. To get a 50% margin you need a 100% markup: $1,000 x 2 = $2,000, where the $1,000 profit is half the price. Markup is measured against cost, margin against price.
How do I convert markup to margin?
Divide the markup by one plus the markup: margin = markup / (1 + markup). For a 25% markup, 0.25 / 1.25 = 20% margin. To go the other way, markup = margin / (1 – margin): a 20% margin needs 0.20 / 0.80 = 25% markup. A markup calculator does this instantly for any value.
What markup should a contractor charge?
Enough to cover overhead and the net profit you want. Add your annual overhead and target profit, divide by expected revenue to get the required gross margin, then convert to markup with margin / (1 – margin). For example, $90,000 overhead plus $50,000 profit on $500,000 revenue needs a 28% margin, which is a 38.9% markup.
Should contractors mark up materials?
Usually yes, because buying, picking up, storing and warrantying materials costs time and money. The rate is a business choice; some use a lower markup on materials than on labor. Contracts can limit it, especially on commercial or insurance work, so check the contract before you set the rate.
What is the difference between gross margin and net margin?
Gross margin is profit after direct job costs, as a percentage of revenue. Net margin is profit after overhead as well. NAHB reports remodelers averaged a 29.9% gross margin but a 6.3% net margin in fiscal 2024, because operating expenses took 23.6% of revenue. Your estimate’s margin is gross; overhead comes out before profit.
What is a good profit margin for a contractor?
One that covers your overhead and leaves the net profit you planned. There is no universal figure; for context, NAHB reports remodelers averaged a 6.3% net margin in fiscal 2024. Work out your own: required gross margin = (overhead + target profit) / revenue, then set your markup percentage from it.
The bottom line
Markup is a percent of cost, margin a percent of price, and they are never the same number. Decide which one you are targeting, build it from your overhead and profit goal, and price by dividing when you think in margin.
Check any number with the markup calculator, read the full estimating guide for where it goes on the page, and build the estimate in our free estimate and invoice maker.